All

"T" Type Pinion Gear Shaft Key Bt 70/99 Spt 88/99 Replaces Hd #11219
Jims shaft nuts now give the ultimate in flywheel holding power. The mating face of each nut has been ground to a 32 surface finish and held square to threads within .0005. This in turn will pull the shafts straight into the flywheels and simplify flywheel truing. We didn't stop there! Each nut is machined on state of the art CNC lathes, and heat treated to make these nuts the toughest and best available on the market.HARDWARE
T Type Pinion Gear Shaft Key
Fits Big Twin Evolution 1990/1999, K Model & Sportster 1988/1999
Package of 10
Replaces HD# 11219

Engine left case roller bearing set .001

Rowe cast iron valve guide is .001 oversize and machined to accept seal.

Rowe cast iron valve guide is .002 oversize and machined to accept seal.

Jims power glide .005 hydraulic tappet assembly includes roller assembly installed. Order adjuster screws or nuts separately.

Kick starter bushing is .005 oversize and includes 1 seal.

Kick starter gear bushing is .005 oversize.

Rowe cast iron valve guide is .008 oversize and machined to accept seal.

02 Sensor Eliminator Plug Use When Removing Oxygen Sen 18X1.5Mm Thread Ego-Plug

• Use the weld nut for exhaust head pipes that have no bung for an oxygen sensor
• Use the eliminator plug when you have eliminated the oxygen sensor from your exhaust & need to plug the existing open hole

Note: 12mm is OE on 2010/Later Dresser modelsRaw Steel Eliminator Plug
18 x 1.5mm thread
(Imported)

BDL 1 rear replacement belt is 133 tooth. 2007-2011 FLST

BDL 1 rear replacement belt is 137 tooth. 2007-2008 FLT

Fork stem die holder is for use with a 1 x 24 TPI fork stem die tool. 1948-1985 FL

Riser set is for use with 1 diameter handlebars. Set features a custom short style with black aluminum billet and a contrast cut. Custom applications

Riser set is for use with 1 diameter handlebars. Set features a custom short style and is constructed with solid brass billet with a contrast cut. Set is cast solid. May have pits and marks from the hand casting process. Custom applications

1 handlebar sleeve constructed of raw steel slides over the original bar end to eliminate stock internal throttle or spark assemblies 1949-1959 FL

1 linkert carburetor rebuild kit includes hardware and all necessary parts to fit linkert carburetors. Kit includes the overhaul kit throttle shaft and its corresponding disc. Additional installation hardware includes: screws bushings throttle shaft spring main nozzle spring float bowl gasket washers intake gaskets needle valve gasket carburetor cork float float pivot pin choke detent ball with spring float needle and seat. 1937-1957 G

Linkert 1 throttle disc is #12 type to fit 1 Linkert carburetors. 1936-1956 G

Shock set will lower by 1 features a black finish. Lower kickstands are also available separately. The distance between eye to eye measures 11-3/4 *Warning: Installing a lowering kit or shorter shocks will decrease initial ground clearance. the motorcycle will be lower to the ground and care should be taken to avoid bottoming especially over bumps or in turns. 2006-2010 XL 883 2009-UP XL 1200C

Shock set will lower by 1 features chrome springs and body caps. Lower kickstands are also available separately. The distance between eye to eye measures 11-3/4 . Warning: Installing a lowering kit or shorter shocks will decrease initial ground clearance. the motorcycle will be lower to the ground and care should be taken to avoid bottoming especially over bumps or in turns. 2006-2010 XL 883 2009-UP XL 1200C

Retro brass riser set is for use with 7/8 -1 handlebars. Set features a sand casting polished finish. Set is cast solid. May have pits and marks from the hand casting process. Custom applications

Brass sand riser set is for use with 7/8 -1 handlebars. Set features a smooth casting polished finish. Custom application

Stainless steel riser set is for use with 7/8 -1 handlebars . Set features a smooth casting polished finish. Custom application

1 Spring Fork stem with washer. Stem will accept stock damper control. 1936-1948 EL 1941-1948 FL

This fork neck cup set is used when installing a Big Twin or late Sportster 1 neck fork assembly on early Sportster models. Allows installation of Spring Forks with a 1 neck stem. Includes dust cover races installed and bearings Remove your existing cups and install these cups into your frame neck and you are ready to install any 1 neck stem fork assembly. *NOTE: Order related spacers and nuts separately. **NOTE: Spacers can be installed on the underside of the neck for added height. 1957-1977 XL 1937-1952 W 1937-1957 G

1 x24 zinc plated spring fork stem hex nut is a duplication of original part. Spring fork hex nut features centering shoulder. 1936-1940 EL 1941-1948 FL 1937-1948 UL

1" Lowered Kickstand Dresser Models 2007/Later* Use On Lowered Bikes

• When you lower your Dresser model, you have to use a shorter kick stand to allow correct lean angle when your bike is parked
• Handcrafted in the USA, TIG welded and hand polished to accept smooth show quality chrome plating
• Mounts on OE bracket and utilizes the OE kick stand spring
• Will also fit years back to 1984, but lean angles may vary

Pingel
Chrome Plated Kick Stand
Length: 1 Lowered ront, 1 Lowered Rear
Fits Dreser models 2007/Later

Oversized Linkert carburetor 1-1/16 venturi is precision machined aluminum and made to exact tolerances for perfect fit and performance. Replacement venturi for M2 M5 M21 M41 M51 M52 M55 M58 M64 M65 M84 and M97 carburetors. 0-Replacement application 1937-1942 WL 1936-1954 G

This 1-1/16 linkert carburetor venturi is precision machined to exact tolerances constructed of aluminum. This venturi is for M2 M5 M21 M41 M51 M52 M55 M58 M64 M65 M84 M88 & M97. 1941-1952 W

Carlisle Panther 1-1/2 rear belt has 133 tooth. 1991-1999 FXD

Carlisle Panther 1-1/2 rear belt has 139 tooth. 1997-2003 FLT

1-1/2 chrome plated steel concho. Sold as a pack of 50. 0-All models

Overhaul kit for 1-1/2 carburetors includes throttle shaft brass float needle and seat float bushings springs float pin gasket carburetor bowl large nut with stud lock washer luck nut and copper filled seal washer. For M74 models. Threads on this needle and seat assembly is 7/16 x 27. *NOTE: For the float arm installation the center prong of the float arm should have .003 of clearance in order for the arm and needle to move freely. 1941-1965 FL 1941-1952 EL